talkFestool  

Go Back   talkFestool > Projects, Methods, and Techniques > Woodworking Projects

Woodworking Projects Chairs to chests, boxes to breadboards? Stop in!

Reply
 
LinkBack Thread Tools Display Modes
  #11 (permalink)  
Old 05-25-2015, 10:23 PM
Poto's Avatar
Super Moderator
 
Join Date: Jul 2008
Location: San Diego, CA
Posts: 8,961
Default Re: Building the Lingerie Chest

I'm also a cheeks-first guy. It's actually pretty fun practicing that cut - just making vertical cut after cut, trying to get them perfectly straight...
__________________
I don't have as many Festools as Fred. Or Marcou's, or Brese's, or Lie-Nielsen's, or Lee Valley's, or Blue Spruce's, or Harold and Saxon's, or...
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
  #12 (permalink)  
Old 06-01-2015, 04:45 PM
derekcohen's Avatar
Member
 
Join Date: Dec 2009
Location: Perth, Australia
Posts: 437
Default Coved Frame-and-Panel

Below is a link to my ongoing build.

http://www.inthewoodshop.com/Furnitu...And-Panel.html

This focussed on taking these parts ..



.. and forming this joint ...



.. to create this curved panel ...



This is just a dry fitting at this stage. The emphasis here is the cove as a transition from frame to panel ..



Hopefully you will find parts to discuss or critique.

Too little available time this weekend for building. I am hopeful of completing the other panel next weekend.

Regards from Perth

Derek
__________________
Articles on furniture construction, shop tools and reviews at http://www.inthewoodshop.com
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
  #13 (permalink)  
Old 06-08-2015, 12:30 AM
Administrator
 
Join Date: Mar 2015
Location: NorCal
Posts: 313
Default Re: Building the Lingerie Chest

Derek, wanted to thank you for this thread. You're way beyond my skill set and tool kit, and I find it all very inspirational and makes me very glad to be a part of this forum.
__________________
---
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
  #14 (permalink)  
Old 06-13-2015, 02:43 PM
derekcohen's Avatar
Member
 
Join Date: Dec 2009
Location: Perth, Australia
Posts: 437
Default Re: Building the Lingerie Chest

Thanks for the kind words Paul. I think that you overestimate my ability ... and underestimate my skill at fixing mistakes!

Regards from Perth

Derek
__________________
Articles on furniture construction, shop tools and reviews at http://www.inthewoodshop.com
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
  #15 (permalink)  
Old 06-13-2015, 02:44 PM
derekcohen's Avatar
Member
 
Join Date: Dec 2009
Location: Perth, Australia
Posts: 437
Default Re: Building the Lingerie Chest

A final few pictures to complete the section on the panels, as we move to planning out the drawer dividers.

Here is the second panel (on the right) ..



While it appears less figured than the first panel completed (on the left), it does have a special charm of its own. Here is a close up of the book matching and the central figure ...



This will give you a little more of an idea of the curve in the design ...





Regards from Perth

Derek
__________________
Articles on furniture construction, shop tools and reviews at http://www.inthewoodshop.com
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
  #16 (permalink)  
Old 06-13-2015, 07:32 PM
Member
 
Join Date: Sep 2011
Location: Oregon USA
Posts: 317
Default Re: Building the Lingerie Chest

Outstanding!
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
  #17 (permalink)  
Old 06-14-2015, 10:46 AM
Ausrob's Avatar
Member
 
Join Date: Aug 2008
Location: Melbourne, Australia
Posts: 485
Default Re: Building the Lingerie Chest

Looks beautiful, Derek.

Regards,

Rob
__________________
http://www.damnfinefurniture.com
I don't have as many tools as most people here...but Gee I've got some pretty hardwoods!
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
  #18 (permalink)  
Old 06-14-2015, 02:48 PM
Wonderwino's Avatar
Super Moderator
 
Join Date: Sep 2008
Location: Grew up in Peekskill, NY; Now living in Northwest Kansas
Posts: 2,857
Default Re: Building the Lingerie Chest

Very graceful curves!

__________________
Water separates the people of the world; wine unites them.

"If you have good manners and are well spoken, you can be welcome anywhere." -Mom, 1959
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
  #19 (permalink)  
Old 06-15-2015, 03:01 PM
derekcohen's Avatar
Member
 
Join Date: Dec 2009
Location: Perth, Australia
Posts: 437
Default Re: Building the Lingerie Chest

It's always a bit disheartening to hit a problem that threatens to derail the project before it has managed to truly get underway.

When we left off last time, the panels were done and I began planning the drawer dividers.



Then I noticed that the join in the book-matched panel on the left had split in near the centre. It was possible to flex it back-and-forth. The lower- and upper sections were still holding. I wiggled a little hide glue into the split and pulled it tight with clamps. I returned after a day, and it looked strong. It had been my plan all along to add 1/4" thick strips at the inside of the panel, which would both stiffen and reinforce. Now it looked like this would be necessary, rather than insurance.

The areas for the 3" wide strips were marked off, and the finish scraped off the centre of each panel. One panel remained intact as this work took place. The other split .. again. Damn and bugger.

My wife said "take it off". I thought I may be getting lucky, but - no - she meant the panel

Thank goodness for hide glue! I had used Titebond Liquid Hide Glue all along. However, I have never had to undo anything before. This was a first.

The first step was to drill out the pins. One side of the hole was covered with waterproof tape and boiling water was poured in. A heat gun added more heat. A clamp was used in reverse direct to push the sections apart. Slowly it moved, and then .... then my camera decided to blow up the memory card, and every photo of this process was lost! Double damn!

I started over today ...



Post-mortum of the panel indicated that the spring joint gap was too large ...



Clamping the pieces together would have squeezed out the glue.

Checking the sides against a straight edge, it was clear which piece was the offender ..



I am not sure if I demonstrated the method I used to joint these thin 1/4" thick panel sections. Well this is how it was done ..

First step was to lift the board up on a 1/2" thick section of MDF (nice and flat). The second piece was added for balance ...



A second piece of MDF was layed on top, and then weighted down with bricks (to ensure the edge was flat and parallel to the bench top ..



A jointer plane was now about to shoot the edge square ..





Generally I plane the centre to create a spring joint, but here I was reducing the existing gap by planing it flatter. In the end it was a very slight, almost imperceptible hollow ..



To glue up, the panel pieces were first work from the back side. Tape was stretched across and used to pull the sections together ..



The full side was done, with the joint line reinforced to minimise glue running out ...



Reversing the panel, glue was spread down the join ..



This could then be opened out, taped together (again with stretched tape), joins levelled with a plastic mallet, and lightly clamped together. Bricks were added to hold everything flat while the glue dried ...



While this is drying, the solid panel received its reinforcing strip ...



The program will be resumed shortly ...

Regards from Perth

Derek
__________________
Articles on furniture construction, shop tools and reviews at http://www.inthewoodshop.com
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
  #20 (permalink)  
Old 06-15-2015, 04:26 PM
CharlesWilson's Avatar
Member
 
Join Date: Jul 2008
Location: Newington, CT
Posts: 332
Default Re: Building the Lingerie Chest

Nice post Derek. Hide glue is responsible for the survival of many ancient pieces of furniture. Thanks for reminding us of its virtues.

Charles
__________________
Tools I Have Made: 3 Mallets, Layout Knife, a 1/8 inch Skew Chisel, a 1/4 inch Skew Chisel, Miter Box, 1/8 inch chisel, 3/32 inch chisel (from 3/32 Champion punch), Tool Cabinet
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump


All times are GMT +1. The time now is 07:00 PM.