talkFestool

talkFestool (http://www.talkfestool.com/vb/)
-   Woodworking Projects (http://www.talkfestool.com/vb/woodworking-projects/)
-   -   Building the Lingerie Chest (http://www.talkfestool.com/vb/woodworking-projects/6618-building-lingerie-chest.html)

Poto 05-25-2015 10:23 PM

Re: Building the Lingerie Chest
 
I'm also a cheeks-first guy. It's actually pretty fun practicing that cut - just making vertical cut after cut, trying to get them perfectly straight...

derekcohen 06-01-2015 04:45 PM

Coved Frame-and-Panel
 
Below is a link to my ongoing build.

http://www.inthewoodshop.com/Furnitu...And-Panel.html

This focussed on taking these parts ..

http://www.inthewoodshop.com/Furnitu..._m70ede146.jpg

.. and forming this joint ...

http://www.inthewoodshop.com/Furnitu...l_me961e0a.jpg

.. to create this curved panel ...

http://www.inthewoodshop.com/Furnitu..._m7b09c2af.jpg

This is just a dry fitting at this stage. The emphasis here is the cove as a transition from frame to panel ..

http://www.inthewoodshop.com/Furnitu...l_30251cbc.jpg

Hopefully you will find parts to discuss or critique.

Too little available time this weekend for building. I am hopeful of completing the other panel next weekend.

Regards from Perth

Derek

PaulG 06-08-2015 12:30 AM

Re: Building the Lingerie Chest
 
Derek, wanted to thank you for this thread. You're way beyond my skill set and tool kit, and I find it all very inspirational and makes me very glad to be a part of this forum. :takebow:

derekcohen 06-13-2015 02:43 PM

Re: Building the Lingerie Chest
 
Thanks for the kind words Paul. I think that you overestimate my ability ... and underestimate my skill at fixing mistakes!:)

Regards from Perth

Derek

derekcohen 06-13-2015 02:44 PM

Re: Building the Lingerie Chest
 
A final few pictures to complete the section on the panels, as we move to planning out the drawer dividers.

Here is the second panel (on the right) ..

http://i13.photobucket.com/albums/a2...psyple2zof.jpg

While it appears less figured than the first panel completed (on the left), it does have a special charm of its own. Here is a close up of the book matching and the central figure ...

http://i13.photobucket.com/albums/a2...psvcgb4ypv.jpg

This will give you a little more of an idea of the curve in the design ...

http://i13.photobucket.com/albums/a2...ps9xhmhdi3.jpg

http://i13.photobucket.com/albums/a2...psjh5ngqmv.jpg

Regards from Perth

Derek

Sta2lt 06-13-2015 07:32 PM

Re: Building the Lingerie Chest
 
Outstanding!

Ausrob 06-14-2015 10:46 AM

Re: Building the Lingerie Chest
 
Looks beautiful, Derek.

Regards,

Rob

Wonderwino 06-14-2015 02:48 PM

Re: Building the Lingerie Chest
 
Very graceful curves!

:scool:

derekcohen 06-15-2015 03:01 PM

Re: Building the Lingerie Chest
 
It's always a bit disheartening to hit a problem that threatens to derail the project before it has managed to truly get underway.

When we left off last time, the panels were done and I began planning the drawer dividers.

http://www.inthewoodshop.com/Furnitu...l_32f96436.jpg

Then I noticed that the join in the book-matched panel on the left had split in near the centre. It was possible to flex it back-and-forth. The lower- and upper sections were still holding. I wiggled a little hide glue into the split and pulled it tight with clamps. I returned after a day, and it looked strong. It had been my plan all along to add 1/4" thick strips at the inside of the panel, which would both stiffen and reinforce. Now it looked like this would be necessary, rather than insurance.

The areas for the 3" wide strips were marked off, and the finish scraped off the centre of each panel. One panel remained intact as this work took place. The other split .. again. Damn and bugger.

My wife said "take it off". I thought I may be getting lucky, but - no - she meant the panel :)

Thank goodness for hide glue! I had used Titebond Liquid Hide Glue all along. However, I have never had to undo anything before. This was a first.

The first step was to drill out the pins. One side of the hole was covered with waterproof tape and boiling water was poured in. A heat gun added more heat. A clamp was used in reverse direct to push the sections apart. Slowly it moved, and then .... then my camera decided to blow up the memory card, and every photo of this process was lost! Double damn!

I started over today ...

http://i13.photobucket.com/albums/a2...ps6nbmdaxt.jpg

Post-mortum of the panel indicated that the spring joint gap was too large ...

http://i13.photobucket.com/albums/a2...psnspty4yp.jpg

Clamping the pieces together would have squeezed out the glue.

Checking the sides against a straight edge, it was clear which piece was the offender ..

http://i13.photobucket.com/albums/a2...psabjenxvs.jpg

I am not sure if I demonstrated the method I used to joint these thin 1/4" thick panel sections. Well this is how it was done ..

First step was to lift the board up on a 1/2" thick section of MDF (nice and flat). The second piece was added for balance ...

http://i13.photobucket.com/albums/a2...psxwddodea.jpg

A second piece of MDF was layed on top, and then weighted down with bricks (to ensure the edge was flat and parallel to the bench top ..

http://i13.photobucket.com/albums/a2...pspeii9svj.jpg

A jointer plane was now about to shoot the edge square ..

http://i13.photobucket.com/albums/a2...psh2m5pels.jpg

http://i13.photobucket.com/albums/a2...psznakkgj1.jpg

Generally I plane the centre to create a spring joint, but here I was reducing the existing gap by planing it flatter. In the end it was a very slight, almost imperceptible hollow ..

http://i13.photobucket.com/albums/a2...psyqljh3ij.jpg

To glue up, the panel pieces were first work from the back side. Tape was stretched across and used to pull the sections together ..

http://i13.photobucket.com/albums/a2...psjm7aicjh.jpg

The full side was done, with the joint line reinforced to minimise glue running out ...

http://i13.photobucket.com/albums/a2...ps5419mkfj.jpg

Reversing the panel, glue was spread down the join ..

http://i13.photobucket.com/albums/a2...psixxyms4o.jpg

This could then be opened out, taped together (again with stretched tape), joins levelled with a plastic mallet, and lightly clamped together. Bricks were added to hold everything flat while the glue dried ...

http://i13.photobucket.com/albums/a2...pst7aqer3z.jpg

While this is drying, the solid panel received its reinforcing strip ...

http://i13.photobucket.com/albums/a2...psbmp21q12.jpg

The program will be resumed shortly ...

Regards from Perth

Derek

CharlesWilson 06-15-2015 04:26 PM

Re: Building the Lingerie Chest
 
Nice post Derek. Hide glue is responsible for the survival of many ancient pieces of furniture. Thanks for reminding us of its virtues.

Charles


All times are GMT +1. The time now is 07:46 PM.